Markets
Aerospace
Automotive / RV
Building & Construction
Industrial
Marine
Specialty
Product Type
Adhesives
Nitrile Rubber
Pliobond
Thermosetting
Applications
Rubber adhesion (aerospace); Waterproofing, above water surfaces (marine); Wood, metal, glass, wallboard (building construction); Primer for vinyl coatings, brick and stone (industrial); Heat exchanger gaskets, electrical applications (specialty); Gaskets, convertible tops (automotive RV)
Packaging
1/2 Pint Can, Pint Can, Quart Can, Gallon Can, 5 Gallon Pail, Drum
Downloads TDS SDS
Videos
Color
PLIOBOND® 30 General Purpose Adhesive
PLIOBOND® 30 adhesive is a general purpose thermosetting adhesive that can be used to bond virtually all porous and non-porous substrates. When cured, PLIOBOND 30 adhesive provides tough, chip-resistant bonds that remain flexible over a wide temperature range. Substrates bonded with PLIOBOND 30 adhesive offer excellent resistance to mechanical shock and oxidization. This adhesive provides outstanding dielectric properties and has low water absorption.
SUGGESTED USES
- PLIOBOND® adhesive can be used as a sealer, primer, water repellent or coating for metal, wood, plastic, plastic film, ceramic, bone, ivory, glass, rubber, paper, leather, plaster, drywall, insulation, concrete, brick and stone
- Assembling electrical appliances and equipment
- Doping electric motor armature coils
- Anchoring non-skid material to floors
- Waterproofing awnings, tarps, convertible tops, outdoor furniture
- Protecting above-water surfaces on watercraft
PLIOBOND® 30 adhesive comes ready to use; no conditioner, accelerator, or catalyst is required.
PLIOBOND 30 adhesive can be applied by spraying, roll coating, knife coating or brushing.
When PLIOBOND® 30 adhesive is stored indoors, out of direct sunlight and in the original, unopened container between 60°F and 80°F (16°C and 27°C), the shelf life is six months. Always rotate stock.
PLIOBOND® 30 adhesive contains ingredients that could be harmful if mishandled. Contact with skin and eyes should be avoided and necessary protective equipment and clothing should be worn. All five-gallon pails and larger metal containers should be grounded and/or bonded when material is transferred. Vapors are heavier than air and may travel along the ground or may be moved by ventilation and ignited by pilot lights, other flames, sparks, heaters, smoking, electric motors, static discharge or other ignition sources at locations distant from material handling point. Never use a welding or cutting torch on or near drum (even empty) because product (even residue) can ignite explosively.
Ruscoe maintains Safety Data Sheets (SDS) on all of its products. Safety Data Sheets contain health and safety information for your development of appropriate product handling procedures to protect your employees and customers.
Our Safety Data Sheets should be read and understood by all of your supervisory personnel and employees before using our products in your facilities.
Typical Properties:
| Base | Synthetic Polymer | |
| Color | Tan | |
| Solids by Weight, % | 30.0±2 | |
| Solvent Formulation | Ketone | |
| Viscosity, Brookfield, cps, Spindle No. 4 @ 10 rpm | 6,000±3,000 | |
| Specific Gravity | 0.896 | |
| Pounds per Gallon @ 77°F (25°C) | 7.46 | |
| Flash Point (Seta Flash) | 20°F (-7°C) | |
| Coverage | 340-360 sq ft/gal/dry mil | |
| Application Temperature | 40°F to 100°F (4°C to 38°C) | |
| Service Temperature | ASTM D-816-10 psi at 500°F (260°C) for 1 hour | |
Typical Values:
Based on material tested in our laboratories but varies from sample to sample. Typical values should not be construed as a guaranteed analysis of any specific lot or as specification items.